Removal of Conformal Coating with Small Sandblasters

Development of conformal coating technology was driven to a large degree by the military and aerospace industries. While conformal coatings are mostly used on populated, printed wiring boards (PWBs), they are also used to protect components such as transistors, diodes, rectifiers, resistors, integrated circuits (ICs) and hybrid circuits including multichip modules (MCMs) and chip-on-board (COB).

Recent environmental regulations and concerns have had a significant impact on both coating materials and application methods, particularly with regard to control of volatile organic compounds and chlorofluorocarbon compounds. VOCs and CFCs have been extensively used as solvent carriers. Manufacturers and suppliers of conformal coating materials have responded by developing non-solvent based coatings and environmentally acceptable methods of application, curing and removal.

It is important to consider how the choice of a conformal coating material affects the rework and repair issues. The need for rework or repair of a conformal coating can occur any time after completion of an assembly due to a variety of process or product requirements and component replacement issues.

A number of methods are available for rework of conformal coatings. These include thermal, chemical, mechanical, plasma and laser-based systems and small sandblasters or “micro abrasive blasters,” which will be the focus of this column.

Micro-abrasive blasters used for conformal coating removal are small sandblasting systems that are commonly used for metal deburring and etching as well as surface preparation. The cutting media is introduced into a compressed air stream and is ejected through a hand piece utilizing tips as small as 0.026″. This is directed at a component or surface area on PCB where the conformal coating has to be removed. This system can remove conformal coating from a single test node, an axial leaded component, a through-hole IC, an SMT component or an entire PCB without any modification to the system for a variety of coating materials. This method provides the most practical and environmentally friendly means for removing conformal coating from PCB assemblies.

Although these small Micro Abrasive Blasters provide the most practical and environmentally friendly means of removal, they also pose a problem. Micro Abrasive Blasters can generate static electricity as the high velocity air and particles impinge on the PWB surface. The ESD voltage generated at the point of contact can cause damage to components and electrical circuits on an assembly.

Equipment manufacturers have used several different approaches to solving the ESD problem. These are: 1) the installation of AC or DC pulsed ionizer bars in the chamber results in a rapid decay of ESD voltages in the work cell and tubing 2) the installation of a point ionizer at the end of the nozzle to dissipate any static charge built-up in the media stream at the point of contact 3) the use of an inline, auto balanced ionizer where the air source is split, one side flowing to the media and the other side flowing to the inline ionizer. This ionized air is then injected into the media stream just before it leaves the nozzle, eliminating the static charge buildup in the media chamber. The ionized air is also pumped into the work chamber. With this type of system, ESD levels are reportedly in the +10V range.

This entry was posted in Hot Wires and tagged , , , , , , , , , . Bookmark the permalink.

3 Responses to Removal of Conformal Coating with Small Sandblasters

  1. John Borneman says:

    Hmmm… I saw no mention of any issues with the media being cast out over the assembly. Are particles from the process left behind on the unit a problem?

  2. Jim Norton says:

    John… Whenever blasting media is used to remove conformal coatings, a clean-up (rinse) process is necessary. Masking the areas not effected by the repair will dramatically reduce the media distribution. Microblasters are typically used for small area repair, in some cases, component recovery. Rather than stripping the entire circuit board, blasting offers the option of selectively removing the coating in small areas. Considering the wide variety of coatings available, you should always contact the vendor that is providing your microblasters and media and have them test the equipement and specify the proper media to match the application. Some conformal coatings do not lend themselves to blasting, so be sure to discuss this with your media supplier.

  3. John Borneman says:

    Thanks, Jim!

Comments are closed.