A gearhead’s guide to some of the chemicals that make up our boards.
![Pb-Free Lessons Learned Pb-Free Lessons Learned](http://circuitsassembly.com/cms_bu/images/stories/column_icons/pbfreelessons.gif)
There’s been a lot of buzz about halogen-free and halide-free products. But what do halogen-free and halide-free actually mean? What exactly are halogens and halides? Why do we want to get rid of them? And why do we use them in the first place? I wanted to find out more about these families of chemicals getting so much attention.
I’m a mechanical engineer, and chemistry was never my strongest suit. When I hear the term “halogen,” I think of automobile headlights with brighter, more focused beams, not flame-retardants that contain bromine. But with the talk about halogen-free and halide-free, I felt compelled to ask a couple of chemists exactly what this meant. Of course, I didn’t understand their first explanation. So I asked them to rephrase their explanation in more basic terms, and they did. We went through this cycle a couple times. Eventually, I got it. It’s actually quite simple. Still, I figured I’m not the only assembly engineer who has forgotten more than they remember about basic chemistry, so this month’s lesson learned is more or less a gearhead’s guide to halogens and halides, with a quick flashback to your high school chem class.
Halogen or halide? A halogen is an element in the seventh column of the periodic table, which includes fluorine, chlorine and bromine. Iodine and astatine complete the group, but are not the subjects of primary consideration for electronics manufacturers. Elemental halogens have seven valence electrons and are very reactive. In their quest to obtain an eighth electron, halogens can be very strong oxidizing compounds. Once a halogen does obtain that eighth electron, it picks up a net negative charge and becomes a halide. Having the net negative charge makes the halide compound ionic. A common example is table salt: Na+Cl-. Some readers also may be familiar with the similar term halite, spelled with a “t” as opposed to a “d.” Halite is the mineral form of NaCl that’s known as rock salt. It’s regularly used in winter climates to melt snow and ice from walkways and roadways.
Where and why are they used? In broad terms, halogens are associated with PWBs and components, while halides are associated with soldering operations. There are exceptions. For the most part, halogenated compounds are found in PCBs, solder masks, mold compounds, connectors, cable insulation and wiring conduit. They are used because they offer flame retardant properties to otherwise flammable plastics. The 1979 ban on polychlorinated bisphenols (the “other” PCB) gave way to the use of brominated organic compounds. Now some of these brominated flame-retardants (BFRs) are on the hit list too. Some halogenated compounds have already been replaced with halogen-free products; others are slated for removal and replacement over the next several years. Bear in mind not all halogenated compounds are toxic. Consider table salt: Ingestion of excessive quantities may not be advisable, but it is certainly not considered a toxic substance.
Here’s one of the exceptions I mentioned: Non-ionic halogenated compounds can also be used as raw materials in soldering fluxes to help keep activators working as process temperatures increase, but they are used in far smaller quantities than in boards or components, and their inclusion is not an absolute necessity. Wave soldering fluxes designed to withstand extended thermal cycles may likely contain halogens, but some of today’s most successful Pb-free wave fluxes and pastes do not. Inclusion of halogens in flux materials is determined by the desired performance characteristics of the flux itself, and is usually fixed early in the product development cycle. If a flux is to be halogen-free, its basic composition must consider the absence of halogens, and other ingredients in the formulation must be selected accordingly.
Although halogens are sometimes included in fluxes, halides are the compounds most commonly associated with them. While halogens can be added to improve a flux’s thermal robustness, halides are added because they can rapidly reduce metal oxides and, in combination with a variety of organic acids, make ideal activator systems. But they have been cited as possible sources of post-soldering corrosion, so manufacturers of high performance and harsh environment electronics traditionally avoid them if they run no-clean processes.
On the other side of the assembly spectrum, manufacturers of more cost-sensitive systems often prefer fluxes that include halides. The halide-containing fluxes provide better wetting during soldering – and therefore, more mechanically reliable solder joints – on lower-cost components and boards more likely to exhibit solderability problems. Because halides can be associated with post-solder corrosion, no-clean fluxes containing halides will always contain rosin to encapsulate any leftover, un-reacted ionic material and ensure electrochemical reliability.
Here’s the other exception I mentioned: Halides are often used in the etching, plating and final finishing processes of PWB fabrication. They sometimes can be found as residual contaminants on bare boards if not cleaned properly. If completed assemblies demonstrate ionic contamination issues, it is wise to check the bare boards to understand whether the contamination source is in the assembly process itself, or if the contaminants were left from fabrication.
Why do we want to eliminate them? A quick Web search revealed some convincing reasons to limit use of specific halogens. If incinerated under certain conditions, they can form dioxins, which are known carcinogens. In structural fires, they can emit toxic gases that prevent victims from escaping (and rescuers from entering) burning areas. In a computer room, a fire in one machine can release acidic fumes that produce catastrophic failures in nearby machines. These combustion-related implications sound horrible, and I’m sure there are plenty of other sound reasons to eliminate halogenated materials. Often, however, it’s the halogenated compounds that permit higher temperature operation and prevent fires in the first place, and elimination or substitution is not a simple process. Just like leaded solder alloys, there are no drop-in replacements for many halogenated products.
How do we define halogen-free and halide-free? Both halogens and halides can be found in trace amounts as impurities in many materials. Therefore, upper limits for the presence of these materials have been set by the following organizations:
The International Electrochemical Commission defines halogen-free as:
- <900 ppm chlorine.
- <900 ppm bromine.
- <1500 ppm total halogens.
IPC defines halide-free as:
- <500 ppm of a flux’s solids content, as chloride (fluoride and bromide are adjusted for molecular weight difference and calculated as chloride).
How do we test for halogens and halides? Halides can be detected using simple spot tests as described in J-STD-004A. They can be quantified using ion chromatography (IC). But halogens themselves are a little more difficult to test for. IC cannot distinguish them unless they are first ionized; the test preparation procedure itself can influence the results. Combustion IC is generally considered a reliable technique that ionizes the halogenated compounds through a combustion process. Another routine analytical technique that can detect halogens (and many other elements) down to the parts-per-billion level is inductively coupled plasma (ICP) spectroscopy. However, neither of these techniques can distinguish between an ionic halide and a non-ionic halogen.
To sum up: A halogen is a chemical element found in many electronics components and is the focus of systematic regulatory elimination. In many cases, there are no simple drop-in replacements for halogenated materials. A halide is an ionic compound that contains a halogen and is often used electively in fluxes to improve soldering performance. Halides may also be subject to elimination in the foreseeable future; by definition they are a type of halogen. The use of halides in fluxes is optional, but some difficult solderability situations demand them. And as for halite, well, depending on where you live, that could be a necessity also. I live in New Jersey and right now we’re expecting a snowstorm, so my next task is to check for the presence of halite in my garage.
Au. note: I had a lot of help gathering and making sense of all this information. Many thanks to my associates Mitch Holtzer, Mike Murphy, Sanju Arora and Mike Liberatore for their inputs and their patience as I compiled it.
Chrys Shea is an R&D applications engineering manager at Cookson Electronics (cooksonelectronics.com); chrysshea@cooksonelectronics.com. Her column appears monthly.