News
Products
‘Soft Landing’ technology on the Condor flying probe test platform addresses concerns manufacturers face over test coverage on complex and high density boards, as well as unwanted damage that can occur with conventional probe techniques.
With ‘Soft Landing,’ the test nail travels towards the component or pad at normal speed until approximately 1 to 2 mm above its target landing position. The speed of the nail is then reduced to soften its impact with the board. This protects delicate components and minimizes the ‘footprint’ where the nail touches the board. In tests, adding a soft landing to an existing nail contact reduced the visible ‘footprint’ by more than a third.
A smaller footprint means more precise positioning in highly dense areas. It also lowers the chance of shorting leads in close proximity to each other, invalidating the test and creating potential damage.
Test coverage increases as more test points can be reached without being damaged or scratched. It only affects the z-axis of travel; Digitaltest MTS system test programs can be updated to take advantage of the technique with minimal additional programming.
Digitaltest GmbH, digitaltest.com
With ‘Soft Landing,’ the test nail travels towards the component or pad at normal speed until approximately 1 to 2 mm above its target landing position. The speed of the nail is then reduced to soften its impact with the board. This protects delicate components and minimizes the ‘footprint’ where the nail touches the board. In tests, adding a soft landing to an existing nail contact reduced the visible ‘footprint’ by more than a third.
A smaller footprint means more precise positioning in highly dense areas. It also lowers the chance of shorting leads in close proximity to each other, invalidating the test and creating potential damage.
Test coverage increases as more test points can be reached without being damaged or scratched. It only affects the z-axis of travel; Digitaltest MTS system test programs can be updated to take advantage of the technique with minimal additional programming.
Digitaltest GmbH, digitaltest.com
JPSA’s large-format laser beam switching module can quickly, accurately switch the entire beam from one path to another (i.e., between two different experiments, or between two separate processes). Has 50 x 50 mm clear aperture for passage of a larger-diameter homogenized beam without beam corner clipping. A vacuum UV (VUV) product, can be used with short-wavelength UV excimer beams including 157, 193 and 248 nm. There is no grease or oil VUV beam delivery designs, and all organic materials have been removed to prevent degradation by UV radiation and contamination of the optics and interior chamber. This switching module can be purged with high-purity gases such as nitrogen.
The industrial-grade product is designed for 24/7 service. Designed for integration into a laser beam delivery system and can deflect the beam out of production when desired to perform beam diagnostics, check beam homogeneity, pulse width or other beam characteristics, since an excimer laser beam changes characteristics over time and usage.
Remote control allows the user to insert or remove a beam splitter; is magnetically pre-mounted so the beam splitter will be accurately located. It has a true gimbal design and allows either a 90-degree turn or straight-through beam path. Switching is mechanical and the unit holds accurate tolerance swing when switching from one path to the next.
JPSA Laser, jpsalaser.com
Electrolock-ESD material is RoHS-compliant to meet regulatory demands for lead-free manufacturing.
Rich Reed, business unit manager, said: "When the 2006 lead-free requirements go into effect, high-temperature performance will become a more critical issue for electronic contract manufacturers. Our Electrolock-ESD material was designed to deliver consistent performance at temperatures in excess of 550°F, without deflection, which ensures a rigid, even surface and optimum machinability."
Rich Reed, business unit manager, said: "When the 2006 lead-free requirements go into effect, high-temperature performance will become a more critical issue for electronic contract manufacturers. Our Electrolock-ESD material was designed to deliver consistent performance at temperatures in excess of 550°F, without deflection, which ensures a rigid, even surface and optimum machinability."
Unlike conventional material solutions, the compound reportedly yields a smooth surface without the need for sanding. Durable surface is impervious to chemical reactions and eliminates glass blooming associated with traditional solder pallet materials.
Comes in a variety of sizes to accommodate a range of applications.
Electolock Inc., electrolock.com
Aquacoat Plus is a water-based conformal coating formulated to protect electronic circuitry. Eliminates the need for extraction and other precautions normally required to apply solvent-based conformal coatings. Is non-flammable, contains low levels of VOCs. It contains no isocyanates, so it can be soldered through without fear of highly toxic gases, and is phenol-free (non-corrosive to cadmium and zinc plates)
Based on polymeric materials, said to offer adhesion on a variety of substrates and a wide operating temperature range. Available in two formulations: WBP and WBPS (Sprayable) for use in selective film coating equipment.
Meets the requirements of DEF-STAN, MIL and IPC-CC-830 and is RoHS compliant.
Electrolube, electrolube.com
Based on polymeric materials, said to offer adhesion on a variety of substrates and a wide operating temperature range. Available in two formulations: WBP and WBPS (Sprayable) for use in selective film coating equipment.
Meets the requirements of DEF-STAN, MIL and IPC-CC-830 and is RoHS compliant.
Electrolube, electrolube.com
U.S. Distributor: Christopher Associates, christopherweb.com
Engineering Data Management (EDM) suite helps engineering teams create RoHS/WEEE compliant products. The database management system enables detailed control over all product design data with emphasis on environmental compliance material content. Supports various versions of RoHS data including RoHS 5 (NIE exemption) and the general RoHS 6 requirements. Can manage all relevant product design data including ECAD (electrical) and MCAD (mechanical) with the capability to create RoHS/WEEE reporting documentation.
Functions include BOM versioning, ECO generation, full library and workflow management, and document archival for the engineering work group.
EMA Design Automation, ema-eda.com
Functions include BOM versioning, ECO generation, full library and workflow management, and document archival for the engineering work group.
EMA Design Automation, ema-eda.com
Symbion S36 post-reflow automated optical inspection system provides inspection for high productivity and first-pass yield. Wizard & Go operation features a user-friendly graphic wizard interface that reduces set-up time and operator requirements. DPIX detection technology, based on specialized 3-D image acquisition and image processing techniques, reportedly ensures high accuracy detection with minimized false calls and without compromising speed. Produces measurement and attribute data for statistical process control (SPC). Integrated ADVISOR software allows users real-time access to data for continual process analysis and improvement.
Orbotech Ltd., orbotech.com
Press Releases
- 4FRONT Solutions Invests in Seica’s PILOT V8 NEXT Flying Probe Tester to Enhance Test Capabilities at DeLand, FL Facility; Mike Sementelli Comments
- FRANK Elektronik invests in high-precision SMT line with ASYS machines; Robert Both Comments
- SASinno Americas Opens State-of-the-Art Facility in Washington, Missouri to Support North American Manufacturers; Mike Young Comments
- ZESTRON Hosts Webinar on “Electronic Assembly Failures, Solutions and Lessons Learned for Long Term Reliability”