caLogo

Products

K7000 circular linear blade depanelizer singulates pre-scored PCBs with tight component spacing. The linear blade is 12" long and has a 0.030" thin symmetrical cutting edge. The circular blade is 3.8" in diameter and has the same cutting edge profile as the linear blade. This blade is mounted on a shaft with the center line passing through the middle of the support bearing. For singulating panels with components such as BGA sockets that encroach on the edge of the board. Unit weighs less than 30 lbs.
 
FKN Systek, www.Fknsystek.com
 
An updated Model 5500 Benchtop Stencil Printer reportedly provides vertical separation of the stencil from the PCB prior to the lifting of the stencil frame. Includes tooling for double-sided boards and dual squeegees mounted to linear slide bearings for side-to-side squeegee motion. Includes squeegees with stainless steel blades and rubber blades. Self-locking dial adjustments permit X, Y, Z, and R axis settings. Maximum print area is 500 x 550 mm, and maximum frame size is 600 x 600 mm. Net weight of approximately 165 lbs.
 

These electrostatic dissipative workstations are certified to meet specific electrical property requirements; said to ensure static dissipation at a safe rate. Pedestals and workbench components can be protected by static dissipative powder-coat finishes available in three standard colors. Feature work surfaces and shelves with static dissipative plastic laminate; have ground bolts with a 12' grounding cord. Can be configured in a variety of heights and lengths, with cabinet pedestals and/or legs.

Lista International Corp., www.listaintl.com
The X3 3-D x-ray system inspects PCBs with BGAs and other hidden solder joints. Gathers multiple oblique images to construct a rendering used in identifying solder and component-related defects on both single and double-sided boards. Selectively uses 2-D or 3-D to inspect specific regions. Permits discrimination between top and bottom sides of boards. A typical inspection program is said to be created in fewer than 45 min. Reportedly is suited for inline or offline applications. Has remote programming and real-time SPC software.
 
YESTech Inc., www.yestechinc.com   

Slic Blade line squeegee blades are said to form a surface with low surface energy. Provide 100% electroformed nickel. Solid electroformed nickel reportedly will not chip or flake. Are said to provide lowest wiping pressure and longest blade life; enhanced stencil life and the least stencil damage. Eliminate solder paste sticking and shearing against the blade.
 
Fine Line Stencil, www.finelinestencil.com
ElectroLaser stencils offer the precision of laser-cut apertures and paste release properties of 100% electroformed nickel. Do not contain the trace elements that are liberated to the aperture walls, causing increased surface roughness. Offer the natural lubricity of electroformed nickel, which improves fine-pitch print consistency. Have a thickness tolerance of ±8% of material thickness selected, and are suitable for applications with surface area ratios to 0.55. Feature positional accuracy of ±0.008% and an aperture dimensional tolerance of ±8 µm (0.0003"). Come in standard material thicknesses of 0.003, 0.004, 0.005 and 0.006". Additional thicknesses available upon request.

Fine Line Stencil, a division of FCT Assembly,
www.finelinestencil.com
The BOMcheck.net web database system enables companies to upload substances declarations to a single location for access by all participating manufacturers. Permits electronics producers to reduce the industry burden of ensuring REACH and RoHS compliance by compiling a centralised master database of substance data from suppliers. Will reportedly reduce costs by providing a central location for sharing data with
multiple manufacturers.
 
ENVIRON and COCIR, www.bomcheck.net
Slic laser-cut stencil is said to have mechanical and thermal properties of standard stainless steel, but superior paste release and aperture wall smoothness. Incorporate a base material with a denser grain structure said to result in fewer voids and the same tensile and yield strength as stainless steel. Have a repeatability of ±16 µm and are suitable for applications with surface area ratios of 0.55 and above. Featuring a positional accuracy of ±12.5 µm (over 600 x 600 mm) and an aperture dimensional tolerance of ±9 µm, the following standard material thicknesses are available: 0.004, 0.005, 0.006, 0.007, 0.008, 0.009 and 0.010". Additional thicknesses available upon request. 
 
Fine Line Stencil, a division of FCT Assembly, www.finelinestencil.com
 
Kwik-Lok 100% stainless steel lifting pins provide convenience, speed, and safety in challenging applications and environments. Provide a 5 to 1 strength factor. Have a 17-4 PH stainless steel forged lifting ring to resist corrosion in harsh environments. Large opening accommodates a wide range of lifting hooks or hardware. Load spreader bar on each ring helps to prevent accidental actuation. Maximum lifting loads from 400 to 1400 lbs. Nominal pin diameters range from 1/4" to 5/8" and grip lengths range from 0.5" to 3.00".

Jergens Inc., www.jergensinc.com
iMonitor 2.0 enables creation of real-time dashboards to monitor the enterprise, factory, and lines in real-time through web browsers. Creates unlimited numbers of interactive and real-time production tracking, materials, utilization and quality dashboards. Dashboards are constructed by dragging-and-dropping gauges, charts and other active elements into a design view, along with graphics such as line pictures or plant drawings. Can activate each element by indicating the xLink data source. Users link any gauge or chart in one dashboard to another dashboard, creating a dashboard site structure for unlimited interactivity. Permits building of slide shows of multiple dashboards that rotate at user-defined time intervals.

Aegis Software Corp., www.aiscorp.com

KD-2077 is a high-speed dispensing system that features three standard dispensing heads for a rate of 0.1 sec/shot. Provides automatic syringe pressure compensation, dot size confirmation, low adhesive warning and independent temperature control for each head. Features up to four adhesive dots per dispense cycle. Supports a range of components from 0603 chips to aluminum electrolytic capacitors, SOPs and QFPs. Is compatible with Chinese RoHS and is backward compatible with KD-775 dispenser.
 
Juki Corp., www.jas-smt.com
The MC-12 pick-and-place is said to pack up to 120 feeders into a 1.25 m x 1.44 m machine. Has a top speed of 36k components per hr. Offers board size support of 510 x 460 mm, component side-view camera, and a complete set of software options. Has 12 mm high-performance electrical intelligent feeder platform. Feeder indexing is controlled using advanced servo controls. Includes self-correcting pickup. Recognition system deploys a moving scan camera; measures the components in X and Y directions and from the side. Reportedly can achieve 72k components per hr. in 2.5 m. Comes with two 60-position feeder bars, with a feeder exchange system and a built-in tape cutter as options. Accepts components from 01005 up to 20 mm x 20 mm; is said to place chips with 50µm accuracy at 3 sigma.
 
Assembléon, www.assembleon.com

Page 376 of 506

Don't have an account yet? Register Now!

Sign in to your account