Products
9600 Series Vibration Isolation Workstation for use in cleanrooms is constructed of stainless steel using cylindrical welded braces for maximum rigidity, minimum flat surfaces and easy wipedown.
An enclosed isolation module, stainless steel valves and vented exhaust maintain compliance with Class 1 and 10 cleanroom standards. Available with electropolish finish (Class 1) or clear passivate finish (Class 10).
Features low natural frequencies and high isolation efficiencies. Under maximum load at 80 psi and 10 Hz, typical vibration isolation efficiencies are 93% with a vertical natural frequency of 1.5 Hz and 95% with a horizontal natural frequency of 1.6 Hz. Has isolated weight capacity of either 800 or 1300 lbs.
Feature the proprietary Active-Air Suspension system ¾ a dual-chamber compressed-air system for vibration damping and a preset “zero deflection” level to compensate for load changes.
Tables are available up to 36” deep and 60” wide. Accessories include guard rails, fixed or sliding shelves, and monitor supports.
Kinetic Systems, kineticsystems.com
An enclosed isolation module, stainless steel valves and vented exhaust maintain compliance with Class 1 and 10 cleanroom standards. Available with electropolish finish (Class 1) or clear passivate finish (Class 10).
Features low natural frequencies and high isolation efficiencies. Under maximum load at 80 psi and 10 Hz, typical vibration isolation efficiencies are 93% with a vertical natural frequency of 1.5 Hz and 95% with a horizontal natural frequency of 1.6 Hz. Has isolated weight capacity of either 800 or 1300 lbs.
Feature the proprietary Active-Air Suspension system ¾ a dual-chamber compressed-air system for vibration damping and a preset “zero deflection” level to compensate for load changes.
Tables are available up to 36” deep and 60” wide. Accessories include guard rails, fixed or sliding shelves, and monitor supports.
Kinetic Systems, kineticsystems.com
The portable USC 400 ultrasonic cleaning system can be taken directly to the stencil printer to clean stencil apertures without the need to reset and calibrate the printer. When the system is offline, it can be used in conjunction with a bench-mounted or stand-alone stencil cleaner.
Features Direct On-Contact Ultrasonic Cleaning to remove Pb-free solder paste particles trapped within stencil apertures.
Benefits include: minimal use of fluids, total aperture penetration, no risk of stencil damage and robust construction. Can be used with solder paste or SMD adhesives, is suitable for stainless and plastic stencils. Cleans pick-and-place nozzles, dispensing needles and probe test pins, and can soften solder paste.
An ultrasonic cup with a dwell timer is optional.
Features Direct On-Contact Ultrasonic Cleaning to remove Pb-free solder paste particles trapped within stencil apertures.
Benefits include: minimal use of fluids, total aperture penetration, no risk of stencil damage and robust construction. Can be used with solder paste or SMD adhesives, is suitable for stainless and plastic stencils. Cleans pick-and-place nozzles, dispensing needles and probe test pins, and can soften solder paste.
An ultrasonic cup with a dwell timer is optional.
Surface Mount Technology (SMT), info@smt.uk.com
PowerMod HP (high power) “B” series connector family features touch-safe female housings, integral positive latches and cable strain relief.
Rated over 350 amps and to 250 amps at a 30º C temperature rise. Accommodates American wire sizes from 1/0 to 4/0 AWG and metric wires from 50 to 95mm². Use Sterling contact technology to offer low electrical resistance. Provides a minimum of 500 mating cycles and is rated for circuit interruption (true hot-plug).
Latching system with distinct blue buttons for clear identification offers security and ergonomics. IP 20 rated (touch safe) for user safety, integral coding key allows unique mating of up to 6 individual connectors. Cable strain relief kit, for all applicable wire sizes, is an option.
Offered in 10 different connector housing types, including right angle, bus bar, panel mount and blindmate/float selections.
Anderson Power Products, andersonpower.com
Rated over 350 amps and to 250 amps at a 30º C temperature rise. Accommodates American wire sizes from 1/0 to 4/0 AWG and metric wires from 50 to 95mm². Use Sterling contact technology to offer low electrical resistance. Provides a minimum of 500 mating cycles and is rated for circuit interruption (true hot-plug).
Latching system with distinct blue buttons for clear identification offers security and ergonomics. IP 20 rated (touch safe) for user safety, integral coding key allows unique mating of up to 6 individual connectors. Cable strain relief kit, for all applicable wire sizes, is an option.
Offered in 10 different connector housing types, including right angle, bus bar, panel mount and blindmate/float selections.
Anderson Power Products, andersonpower.com
Agile 9.2, the latest release for managing the enterprise product record throughout the product lifecycle, features enhanced functionality and expands on compliance, product portfolio, product collaboration and quality management modules. Supports Linux operating systems, for flexibility, improved intellectual property security and reduced cost of ownership.
Product Governance and Compliance—Provides expanded capabilities to manage Bill of Substance information and rollup compliance information using a variety of scenarios. Has improved supplier declaration capability and regulatory information for effective compliance. Includes upgraded Bill of Substance adapters for Agile partners - PartMiner, i2 technologies, Avent and Arrow.
Product Portfolio Management— Includes executive portfolio analytics and bi-directional integration with Microsoft Project, to provide tightly synchronized program and product information, maximized resource utilization and cross-program visibility and decision support. Portfolio analytics include time to market, financial, resources pool, program and issues tracking.
Product Collaboration—Has enhanced change collaboration and document management capabilities, providing each stakeholder in the extended design and supply chain secure access to critical product record data, including bills of material, attributes, manufacturers, configurations, specifications, documents, models, work instructions, revisions and more.
Improved Global Interface—PLM portfolio is completely localized in six different languages: English, French, German, Japanese, traditional Chinese and simplified Chinese.
Product Quality Management— (previously called the Product Service and Improvement solution) Includes advanced analytics capabilities to tightly integrate customer, product, quality and regulatory information within a closed-loop corrective action system. Enables companies to fulfill customer demands for higher quality, faster response and compliance with regulatory requirements.
Linux Support –Adds the Linux open source operating system to its supported environments. Supports Red Hat Linux AS version 4.0.
Agile Software Corp., agile.com
Product Governance and Compliance—Provides expanded capabilities to manage Bill of Substance information and rollup compliance information using a variety of scenarios. Has improved supplier declaration capability and regulatory information for effective compliance. Includes upgraded Bill of Substance adapters for Agile partners - PartMiner, i2 technologies, Avent and Arrow.
Product Portfolio Management— Includes executive portfolio analytics and bi-directional integration with Microsoft Project, to provide tightly synchronized program and product information, maximized resource utilization and cross-program visibility and decision support. Portfolio analytics include time to market, financial, resources pool, program and issues tracking.
Product Collaboration—Has enhanced change collaboration and document management capabilities, providing each stakeholder in the extended design and supply chain secure access to critical product record data, including bills of material, attributes, manufacturers, configurations, specifications, documents, models, work instructions, revisions and more.
Improved Global Interface—PLM portfolio is completely localized in six different languages: English, French, German, Japanese, traditional Chinese and simplified Chinese.
Product Quality Management— (previously called the Product Service and Improvement solution) Includes advanced analytics capabilities to tightly integrate customer, product, quality and regulatory information within a closed-loop corrective action system. Enables companies to fulfill customer demands for higher quality, faster response and compliance with regulatory requirements.
Linux Support –Adds the Linux open source operating system to its supported environments. Supports Red Hat Linux AS version 4.0.
Agile Software Corp., agile.com
‘Soft Landing’ technology on the Condor flying probe test platform addresses concerns manufacturers face over test coverage on complex and high density boards, as well as unwanted damage that can occur with conventional probe techniques.
With ‘Soft Landing,’ the test nail travels towards the component or pad at normal speed until approximately 1 to 2 mm above its target landing position. The speed of the nail is then reduced to soften its impact with the board. This protects delicate components and minimizes the ‘footprint’ where the nail touches the board. In tests, adding a soft landing to an existing nail contact reduced the visible ‘footprint’ by more than a third.
A smaller footprint means more precise positioning in highly dense areas. It also lowers the chance of shorting leads in close proximity to each other, invalidating the test and creating potential damage.
Test coverage increases as more test points can be reached without being damaged or scratched. It only affects the z-axis of travel; Digitaltest MTS system test programs can be updated to take advantage of the technique with minimal additional programming.
Digitaltest GmbH, digitaltest.com
With ‘Soft Landing,’ the test nail travels towards the component or pad at normal speed until approximately 1 to 2 mm above its target landing position. The speed of the nail is then reduced to soften its impact with the board. This protects delicate components and minimizes the ‘footprint’ where the nail touches the board. In tests, adding a soft landing to an existing nail contact reduced the visible ‘footprint’ by more than a third.
A smaller footprint means more precise positioning in highly dense areas. It also lowers the chance of shorting leads in close proximity to each other, invalidating the test and creating potential damage.
Test coverage increases as more test points can be reached without being damaged or scratched. It only affects the z-axis of travel; Digitaltest MTS system test programs can be updated to take advantage of the technique with minimal additional programming.
Digitaltest GmbH, digitaltest.com
JPSA’s large-format laser beam switching module can quickly, accurately switch the entire beam from one path to another (i.e., between two different experiments, or between two separate processes). Has 50 x 50 mm clear aperture for passage of a larger-diameter homogenized beam without beam corner clipping. A vacuum UV (VUV) product, can be used with short-wavelength UV excimer beams including 157, 193 and 248 nm. There is no grease or oil VUV beam delivery designs, and all organic materials have been removed to prevent degradation by UV radiation and contamination of the optics and interior chamber. This switching module can be purged with high-purity gases such as nitrogen.
The industrial-grade product is designed for 24/7 service. Designed for integration into a laser beam delivery system and can deflect the beam out of production when desired to perform beam diagnostics, check beam homogeneity, pulse width or other beam characteristics, since an excimer laser beam changes characteristics over time and usage.
Remote control allows the user to insert or remove a beam splitter; is magnetically pre-mounted so the beam splitter will be accurately located. It has a true gimbal design and allows either a 90-degree turn or straight-through beam path. Switching is mechanical and the unit holds accurate tolerance swing when switching from one path to the next.
JPSA Laser, jpsalaser.com
Electrolock-ESD material is RoHS-compliant to meet regulatory demands for lead-free manufacturing.
Rich Reed, business unit manager, said: "When the 2006 lead-free requirements go into effect, high-temperature performance will become a more critical issue for electronic contract manufacturers. Our Electrolock-ESD material was designed to deliver consistent performance at temperatures in excess of 550°F, without deflection, which ensures a rigid, even surface and optimum machinability."
Rich Reed, business unit manager, said: "When the 2006 lead-free requirements go into effect, high-temperature performance will become a more critical issue for electronic contract manufacturers. Our Electrolock-ESD material was designed to deliver consistent performance at temperatures in excess of 550°F, without deflection, which ensures a rigid, even surface and optimum machinability."
Unlike conventional material solutions, the compound reportedly yields a smooth surface without the need for sanding. Durable surface is impervious to chemical reactions and eliminates glass blooming associated with traditional solder pallet materials.
Comes in a variety of sizes to accommodate a range of applications.
Electolock Inc., electrolock.com
Aquacoat Plus is a water-based conformal coating formulated to protect electronic circuitry. Eliminates the need for extraction and other precautions normally required to apply solvent-based conformal coatings. Is non-flammable, contains low levels of VOCs. It contains no isocyanates, so it can be soldered through without fear of highly toxic gases, and is phenol-free (non-corrosive to cadmium and zinc plates)
Based on polymeric materials, said to offer adhesion on a variety of substrates and a wide operating temperature range. Available in two formulations: WBP and WBPS (Sprayable) for use in selective film coating equipment.
Meets the requirements of DEF-STAN, MIL and IPC-CC-830 and is RoHS compliant.
Electrolube, electrolube.com
Based on polymeric materials, said to offer adhesion on a variety of substrates and a wide operating temperature range. Available in two formulations: WBP and WBPS (Sprayable) for use in selective film coating equipment.
Meets the requirements of DEF-STAN, MIL and IPC-CC-830 and is RoHS compliant.
Electrolube, electrolube.com
U.S. Distributor: Christopher Associates, christopherweb.com
Engineering Data Management (EDM) suite helps engineering teams create RoHS/WEEE compliant products. The database management system enables detailed control over all product design data with emphasis on environmental compliance material content. Supports various versions of RoHS data including RoHS 5 (NIE exemption) and the general RoHS 6 requirements. Can manage all relevant product design data including ECAD (electrical) and MCAD (mechanical) with the capability to create RoHS/WEEE reporting documentation.
Functions include BOM versioning, ECO generation, full library and workflow management, and document archival for the engineering work group.
EMA Design Automation, ema-eda.com
Functions include BOM versioning, ECO generation, full library and workflow management, and document archival for the engineering work group.
EMA Design Automation, ema-eda.com
Symbion S36 post-reflow automated optical inspection system provides inspection for high productivity and first-pass yield. Wizard & Go operation features a user-friendly graphic wizard interface that reduces set-up time and operator requirements. DPIX detection technology, based on specialized 3-D image acquisition and image processing techniques, reportedly ensures high accuracy detection with minimized false calls and without compromising speed. Produces measurement and attribute data for statistical process control (SPC). Integrated ADVISOR software allows users real-time access to data for continual process analysis and improvement.
Orbotech Ltd., orbotech.com
Green Monster! ESD stencil wiping rolls prevent static buildup and do not use weak paper or tissue fibers. Paper or tissue is typically only held together by weak hydrogen bonds which are quickly destroyed when wet. Instead, they use thicker and coarser rayon fibers that absorb solvents.
With coarse fibers, the porosity is higher, more vacuum can be used to clean solder paste from the apertures, and they are conducive to an aggressive cleaning surface.
High-Tech Conversions, high-techconversions.com
32K443-800 connector has a four-hole flange mounting structure, with a separate center contact pin soldered to the signal via the board. The connector is reusable, extra center contact pins are available. Said to have excellent electrical performance up to 18 GHz.
SMCC (surface mount coaxial connector) products provide an impedance match if the signal trace or signal via on the board is 50 Ohm.
SMCC (surface mount coaxial connector) products provide an impedance match if the signal trace or signal via on the board is 50 Ohm.
Rosenberger provides custom footprints to its customers, developed based on the connector and board models that optimize RF performance.
Rosenberger of North America, rosenbergerna.com
Press Releases
- KIC Expands Footprint in Mexico to Deliver Faster, Localized Support
- ECIA Executive Conference Announces Session on eCrime Tradecraft
- ICZOOM Group Inc. Announced the Launch of PCB & SMT Services to Strengthen One-Stop Electronics Industry Solution at IIC Shenzhen 2025
- Amtech Unveils Proprietary Automation Model for High-Mix, Low-Volume Manufacturing